Antennas pole for rotor cage or to be fixed to the wall with brackets,...
Antennas pole for rotor cage or to be fixed to the wall with brackets,...
60-80mm Boom-Mast Interface Plate for Large Antennas.
Support for rotary dipoles and Boom-Mast interface (dipole center)Optimized drilling for 30-32-35mm insulating supportsDrilling for U bolt from 48-50mm6060 aluminum.The dipole center can be set up and completed by adding to the order the insulating collars and the stainless steel bolts
Monofilament suitable for guy wiring.Max Load 500 kgDuration: 30 years.
Monofilament suitable for guy wiring.Max Load 1100kgDuration: 30 years.
Hardware kit needed for each one guy wire.Material: Stainless steel.
Balun 1:1 on ferrite rod, suitable for rotary dipoles and yagi Max power: 1,5Kw SWR: 1.1 1-52Mhz SO239 Complete with connecting wires jumper.
Balun 1: 1 5 KW pep, ferrite core, suitable for rotary dipoles and yagi Bandwidth: 1-30Mhz SO239 Complete with connecting wires jumper
Balun 1:1, 1.5 KW pep, ferrite core, suitable for wire dipoles Bandwidth 1-60Mhz SO239 Complete with connecting wire jumper
Balun 1:1, 5 KW pep, ferrite core, suitable for wire dipoles Bandwidth 1-30Mhz SO239 Complete with connecting wire jumper
Remote 2-way switch controlled via coaxial cable.SO 239 connectorsRange 1-80Mhz SWR <= 1:1-2Insertion Loss: 0.1dBMax power 1,5KW pepMax VDC 12V 0.15A
Couple of interfaces to send VDC trought coaxial cable.SO239 connectors1-80Mhz rangeMax power 1,5KW pepMax VDC 48V 1A
Bundle kit to realize the interface with which to introduce and withdraw a direct voltage on coaxial cable (T-bias).Amphenol original SO239 connectorsRange 1-30MhzMax power 1,2KW pepMax VDC 48V 1A
Plastic collars for 80 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires 10-12MA bolts
Plastic collars for 60 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 10-12MA
Plastic collars for 50 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 80x6MA
Plastic collars for 45 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 80x6MA
Plastic collars for 40 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 70x6MA
Plastic collars for 35 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 70x6MA
Plastic collars for 32 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 70x6MA
Plastic collars for 30 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 60x6MA
Plastic collars for 25 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 50x6MA
Plastic collars for 20 mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 50x6MA
Plastic collars for 16mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 40x6MA
Plastic collars for 16mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 6MA, lenght iaw with plate or boom pipe tickness.
Plastic collars for 16mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 6MA, lenght iaw with plate or boom pipe tickness.
Plastic collars for 8mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 6MA, lenght iaw with plate or boom pipe tickness.
Plastic collars for 6mm OD tubes.The collar consists of two halves and is supplied without bolts to be ordered separately.It requires bolts 6MA, lenght iaw with plate or boom pipe tickness.
Stainless steel hallen Bolt 40x6MA
Stainless steel hexagon socket head bolt complete with washer and self-locking nut (ATB)
Standard rotator cage.Included thrust bearing and 2m mast pipe Od 48mmPluggable into tubes with an inner diameter of at least 43mm.Universal drilling for Prosistel rotors, CDE / HAM, Create, Daiwa, Kempro, Yaesu etc.
Standard HD rotator cage.Included thrust bearing and 2m mast pipe Od 48mmPluggable into tubes with an inner diameter of at least 50mm.Universal drilling for Prosistel rotors, CDE / HAM, Create, Daiwa, Kempro, Yaesu etc.
Custom rotator cage.Included thrust bearing and 2m mast pipe Od 48mmPluggable on tubes with an outer diameter of 42-52mm.Universal drilling for Prosistel rotors, CDE / HAM, Create, Daiwa, Kempro, Yaesu etc.
HD rotator cage.Included thrust bearing and 2m mast pipe Od 48mmPluggable on tubes with an outer diameter of 50-68mm.Universal drilling for Prosistel rotors, CDE / HAM, Create, Daiwa, Kempro, Yaesu etc.
The folding base enabling you to operate the vertical antennas or dipoles V with minimal effort.It is especially useful on roofs with tiles, where getting around is not particularly easy but also be comfortable on the terraces or in the garden.Pipe diameter = 48x3mm Total height = about 1,5m (5ft) It may be engaged in tubes having an inner diameter of at...
The folding base enabling you to operate the vertical antennas or dipoles V with minimal effort.It is especially useful on roofs with tiles, where getting around is not particularly easy but also be comfortable on the terraces or in the garden.Pipe diameter = 48x3mm Total height = about 1,5m (5 ft)It can be installed on the side of pipes with outer...
The star base makes it possible to easily install a small tubular mast or vertical antennas.It is particularly useful on terraces or land, where there are no other anchor points.Leg length = 1mTotal height = 60cm approxMast diameter = 60mm with bolts to tighten.Accepts mast up to 53mm,Material: Hot-dip galvanized steel, stainless steel nuts and bolts.
The star base with folding mast allows you to easily maneuver vertical antennas or V-shaped dipoles with minimal effort.It is particularly useful on terraces or land, where there are no other anchor points.Leg length = 1mTotal height = 1.7m approximatelyMast diameter = 48x3mmMaterial: Hot-dip galvanized steel, stainless steel nuts and bolts.
The foldable base allows you to easily maneuver vertical antennas, even very heavy or long with minimal effort.It is particularly useful for vertical antennas of 80 or 160m.To be installed on a solid rock or concrete platform.Insulating collar available for diameters 76 or 80mm (specify when ordering)
Telescopic vertical antenna kit for 80m or inverted L for 160m.Initial diameter 80x2mmEnd diameter 8x1mm (adjustable)Weight: about 18Kg
Base bracket for vertical antennas or replacment part.Material: Stainless steelInsulators 30-32-35mm (specify in the order)U bolts 50mm 8MA (anchored to poles from 40-50mm)SO239 connectorRF Choke include (DC grounded)Stainless steel screws
Base bracket for vertical antennas or homemade parts.Material: Stainless steel thickness 3mmAccept insulators from 30-32-35mm and bolts 6MAAccepts U Bolts 40 to 50mm 8MAPrepared for SO239 connector
Central insulator machined to size to 35x2mm pipes (31 mm internal) Material: Delrin
Central insulator machined for 30x2mm pipes (26 mm internal) Material: Delrin
Insulator spacer in ABS for assembling dipoles with parallel wires or Morgain antennas.Spacing between wires = 5cmAccepts wire with outside diameter ~ 4mm Mounting by 3x10MA screws or pop rivets 3x10mm
Potentiometer 10K, spare part for rotators PST641, 2051, 61, 71 series A-B-C-D
UP-Grade Kit for controllers D - D/PRO e COMBO move from RS232 to USB
UP-Grade Kit for controllers D - D/PRO e COMBO move from RS232 to ETHERNET
Antenna rotator cable for Prosistel D series 2x1mm2 4x0.5mm2 1 schield (increases protection against atmospheric discharge and galvanic currents) De = about 8mm The cable can also be used on other rotors that require the same number of wires.
Prosistel D/E-PRO series antenna rotor cable
Guy wires anchor plateCapacity 1000KgHot galvanized steelDiameter 135mmHoles x 10MA
With this additional kit antennas PST-152TV, PST-1524TV and PST-24TV also operate on 6m.
Flange for vertical antennas guy wires Inner hole 25mm (other diameters on request)
Insulator for V-UHF yagi elementsAccept 6mm elementsSquare boom of 20 or 25mmNeed a 4MA stainless steel bolt with self-locking nut
SS U bolt for 35-38mm square tube
SS U bolt for 40-42mm square tube
With this upgrade kit you add the band of 40m to the following antennas: PST-152TV - PST-27TV - PST32 - PST33 -PST35 - PST54 - PST-DDR5 - PST-DDR6-30 - PST-RD152T - PST-RD27T - PST152VC
With this expansion kit, the 30m band is added to the following base antennas: PST-152VC - PST-27VC
With this upgrade kit you add the band of 40m to the following antennas: PST-152TV - PST-27TV - PST32 - PST33 -PST35 - PST54 - PST-DDR5 - PST-DDR6-30 - PST-RD152T - PST-RD27T - PST152VC
With this upgrade kit you add the band of 40m to the following antennas: PST-152VC - PST-27VC
The base allows you to easily install vertical antennas with solid or wire radials.Down bolting assembly.It is particularly useful on roofs with tiles, where moving is not particularly easy but is comfortable even on terraces or in the garden.Mast = 1000x48x3mmPlate = 250x250x6mm holes for 10MA
Wire: Copper 19 X 0.29mmWire diameter: 1.45 mmSection: 1.25 sq.mmElectrical resistance: 15 Ohm / KmSheath: black PE with UV filterSheath diameter: 3 mmTear resistance: 45 KgWeight: 1.338 Kg / 100m
Terminal isolator for wire antennasMaterial: Delrin
Wall-mounted pole-holder bracketMaterial: Hot dip galvanized steelAccepts poles from 40 to 52mmHole for 10mm fixing bolts
Arm for vertical mounting for lightweigth V-Uhf yagi antennas
12m expansion kit for modular dipoles
15m expansion kit for modular dipoles
Solid loaded radial for VF-VC series vertical antennasAvailable for the following bands: 10 - 12 - 15 - 17 - 20 - 30 - 40mEach radial covers one bandSpecify the required band or bands in the order.It replaces the corresponding wire radial for each one operating band.Slightly reduces efficiency and usable bandwidth.Requires calibration
Spare part for rotators PST-61, 71 series D
Spare part for rotators PST-641, 2051, 61, 71, 110, 130 series D and D-PRO
Antennas pole for rotor cage or to be fixed to the wall with brackets, possibly combined with https://www.prosistelshop.com/en/wall-mounted-pole-holder-bracket-288.html
Antennas pole for rotor cage or to be fixed to the wall with brackets, possibly combined with https://www.prosistelshop.com/en/wall-mounted-pole-holder-bracket-288.html